Is my airbag system compatible with my gear (jacket, suit)?

Wearing the airbag system with jackets

Compatible under certain conditions

  • If your airbag is equipped with the "Essential" module

compatibility-chest-03102024.jpg

The Essential module covers the back, neck, chest, and abdomen.

A = Jacket width under the armpits

B = Chest circumference with the gear that will be worn during the use of the product (without the airbag vest)

  • Step 1 - Measure A
  • Step 2 - Calculate 2 x A
  • Step 3 - Subtract B from the result of step 2 to get measurement M

➜ If M is less than 13, then your gear is incompatible

➜ If M is greater than or equal to 13, then your gear is compatible

 

The Performance module covers the back, neck, shoulders, chest, and ribs.

compatibility-chest-03102024.jpg

A = Jacket width under the armpits

B = Chest circumference with the gear that will be worn during the use of the product (without the airbag vest)

  • Step 1 - Measure A
  • Step 2 - Calculate 2 x A
  • Step 3 - Subtract B from the result of step 2 to get measurement M

➜ If M is less than 13, then your gear is incompatible

➜ If M is greater than or equal to 20, then your gear is compatible

compatibility-waist-03102024.jpg
If the total is between 13 and 20, carry out the following additional measures:

D = Jacket width at the waist

E = Waist circumference with the gear that will be worn during the use of the product

  • Step 4 – Measure D
  • Step 5 – Calculate 2 x D
  • Step 6 – Subtract E from the result of step 2 to obtain measurement N

➜ If N is less than 18, then your gear is incompatible

➜ If N is greater than or equal to 18, then your gear is compatible

⚠ WARNING: Measurements are made with the gear that will be worn during the use of the airbag product (sweater, additional protection, removable lining, etc…)

⚠ WARNING: Measurements should be taken with the jacket stretched

 

🛈 Motorcycle gear (textiles or leathers) is elastic and deforms (due to usage, sunlight, movements you make, etc.) allowing the airbag to find the necessary space to deploy at optimal pressure and thus absorb the impact energy.

🛈 The In&motion airbag system can thus be worn under any jacket, provided that the above procedure is followed to ensure there is enough room for the airbag to deploy.

 

Wearing the airbag system under 1-piece motorcycle racing suits

Compatible under certain conditions

The compatible suits tested by In&motion are listed below:

10 Ixon suits: Vortex 2Vortex Lady, Falcon, VendettaVendetta EvoJackalLegendary, Vortex 3, Vortex 3 Lady (specific size guide for this product), Demonio, (Ixon size guide)

2 Furygan suits: Full Ride, Overtake (Furygan size guide)

3 Held suits: Slade II, Expite, Brands Hatch (Held size guide)

1 Klim suit (road use only): Hardanger (Klim size guide)

3 Gimoto suits: Aragon Air, LTD Air, Mugello Air (Gimoto size guide)

1 ONE-X suit: X-RACE

1 Matt Racing suit: BLACK EDITION and its variants GP, MERCURY and MXR-S

1 Mass Sport suit: Mass Air INM1

3 Moto Privée suits: Factory Line CE, Replica Line, Racing line

Additionally, note that leather suits from our partner brand RST come with the In&motion airbag system already integrated.

 

⚠ WARNING: Using the In&motion airbag system with an incompatible suit could lead to improper functioning of the system in the event of an incident.

⚠ WARNING: For your safety, if your suit already has a back protector, consider removing it when wearing the airbag. Wearing an additional back protector on top of the one already present in your airbag product might compromise the proper deployment of the system.

⚠ WARNING: The In&motion system is compatible provided you choose a suit that fits your body shape and follows the manufacturer's size guide.

 

Wearing the airbag system with motorcycle zip-in jackets and pants

Compatible under certain conditions

The motorcycle jacket must be compatible.

The size of the pants must match the manufacturer's size guide.

For leather suits, the pants must also have a stretch zone in the crotch area.

If the suit is a product with an integrated airbag, it is compatible if the pants are the associated model.

One of the 2 parts of the zipper, either the jacket side or the pants side, must be mounted on a flexible area (stretch fabric or mechanical flex):

  • At least 3 cm for a textile product
  • At least 5 cm for a leather product

 

Wearing the airbag system with motorcycle zip-in liner products

Compatible under certain conditions

If the In&motion airbag system is in the form of a zip-in liner (Held eVest Clip-In and Furygan Fury Airbag System Liner), it is compatible with the range of clothing defined by the brand in which the liner can be zipped in.